Bingo Plus stock

List of catalogs of this article:

• 1,Bingo Plus stock Common faults and maintenance methods of automobile engines.
• 2, engine's Repair method
• 3, Can the engine cylinder be repaired?
• 4, What are the general repair methods for car engines?

Common faults and maintenance methods of automobile engines.

1. Fault 1: Engine overheating fault. Due to the special structure of the car engine, it is easy to have excessive coolant temperature during operation.Once the coolant temperature exceeds the normal value, the engine cannot dissipate heat normally, which will cause the engine to overheat and affect the normal operation of the engine. Fault 2: The smell of the engine compartment.

2. Fault phenomenon: The engine works normally when it runs at medium or above speed. When the speed is idle or close to idle, the idle speed is unstable or even shutdown occurs, that is, the idle speed failure is bad. ( 2) Cause of failure: Poor idle speed is usually caused by the intake system and fuel injection control system, and in some cases, poor idle speed is also caused by engine mechanical failure.

3. Common faults and elimination methods of automobile engines: diagnostic elimination methods and procedures. 1 Start gear, the starter and engine cannot run, and the start-up system fault should be detected.

engine repair method

1. Engine repair method Regarding overhaul, we mentioned a comparative overhaul method called medium repair. Zhongxiu is actually a way of three-party cars.

2. Crankshaft bearing wear: If it is found that the engine noise is too loud and there is a "knocking" sound, it may be caused by the wear of the crankshaft bearing.At this time, the crankshaft bearing needs to be replaced to return to normal operation. Improper valve adjustment: If it is found that the engine noise is too loud and there is a "stuttering" phenomenon, it may be caused by the incorrect valve gap.

3. Maintenance skills of automobile engines. Automobile engines are devices that provide power for automobiles and are the heart of automobiles, which determine the dynamics, economy, stability and environmental protection of automobiles. -, maintenance three filters: three filters refer to: gasoline filters, air filters and oil filters.

4. Maintenance strategy for common engine faults. Control the consumption of lubricating oil. The normal operation of the engine inevitably consumes a certain amount of lubricating oil. Abnormal lubricating oil consumption often corresponds to some kind of engine failure.

5. Solution: You should go to the repair shop for replacement and repair in time.Unscling the radiator cover, I found that there were always some oil stains floating on the water, and I found that there was moisture when changing the oil. Reason analysis: The engine has two major circulation systems, one is the coolant circulation system and the other is the lubricating oil circulation system. The two systems are not connected to each other.

Can the engine cylinder be repaired?

Slight pull-cylinder can be repaired. Pull-cylinder means that the inner wall of the cylinder is pulled into a very deep groove. When the piston and piston ring rub against the cylinder wall, it loses sealing, resulting in a decrease in the compression pressure of the cylinder and the loss of power. The reasons for pulling the cylinder are as follows: the gap between the piston and the cylinder is too small.

The engine cylinder can be repaired. If it is serious, it needs to be replaced: the engine cylinder refers to the inner wall of the cylinder.There are obvious longitudinal mechanical scratches and scratches within the range of motion of the piston ring. In severe cases, melting wear occurs, resulting in engine start-up difficulties or self-extinguishing faults.

Hello! The cylinder can be repaired, but it is not recommended to be repaired. The time of repair cannot be guaranteed. It is recommended to directly replace the cylinder liner and piston ring, so as to be more secure.

There is no simplest repair method for pulling the engine cylinder. The repair method should be selected according to the specific situation. If the engine is slightly pulling the cylinder, the piston and piston ring can be replaced, and then the cylinder wall can be slightly ground.

When the situation is mild, it can be repaired. However, when the cylinder wall and piston assembly are seriously damaged, they cannot be repaired. The engine cylinder can also be repaired. Specifically: engine cylinder is a serious engine accident.This refers to obvious longitudinal mechanical damage and scratches on the inner wall of the cylinder within the range of movement of the piston ring.

If it is only a slight pull cylinder, it is easy to repair, change a piston and piston ring, and bring a slight grinding cylinder wall.

What are the general repair methods for car engines?

1. Engine repair method Regarding overhaul, we have proposed a comparative overhaul method called mid-repair. Zhongxiu is actually a way of three-party cars.

2. Maintenance and upkeep method of automobile engine 1. Use good quality engine oil. Engine oil, that is, the lubricating oil of the engine, can play the role of lubricating, cleaning, cooling, sealing, wear reduction and so on. Only the use of qualified lubricating oil can reduce the wear of engine parts and extend the service life.

3. Use the battery wiring method to borrow the power supply of other vehicles to charge. The specific method is to prepare two relatively thick wires. If they are purchased in the market, they are generally divided into red and black. One end of the red line can be connected to the positive pole with the tram battery, and the other end can be connected to the positive pole of the lost tram battery.

4. The more advanced removal methods are ultrasonic removal and nuclear spray removal, but the most used and simplest methods are physical removal and chemical removal. These two methods can also be used at the same time.

5. The following are the car repair methods sorted out for you by the editor. I hope it can help you. The method of car repair is from simple to difficult. When a car drives into a repair shop, we can learn the faults that need to be eliminated from the maintenance. For example: the engine fault light is on, the idle speed is unstable, black smoke is coming out, the refueling is weak, the automatic transmission does not increase the gear and the gear slips, etc.